SubjectThis directive provides the requirements for the entry for all wood packaging materials including dunnage, pallets or crating made from non-manufactured wood entering Canada from all areas except the continental United States (US). It also outlines the disposal or processing procedures for all regulated wood packaging materials not meeting the entry requirement. "The IPPC has recently revised the treatment conditions for methyl bromide fumigation within International Standard for Phytosanitary Measures (ISPM) No. 15: Guidelines for Regulating Wood Packaging Material in International Trade. Wood packaging entering Canada from all areas except the continental US must now be treated and certified in accordance with the new prescribed requirements" Table of Contents Review 1.0 General Requirements 2.0 Specific Requirements 4.0 Non Compliance 5.0 List of Appendices ReviewThis directive will be reviewed every five years, unless otherwise needed. The next date of review is July 24, 2011. The contact for this directive is Joanne Rousson. For further information or clarification, please contact the Forestry Section. EndorsementApproved by:
Amendment RecordAmendments to this directive will be dated and distributed as outlined in the distribution below. Distribution
IntroductionThe risk represented by wood packaging materials and dunnage varies depending on the quality, conditioning and degree of finishing of the wood. The better the quality of wood used, the less likely it is that the wood packaging materials may be infested with serious pests. Many exotic plant pests have been intercepted on wood dunnage, pallets, crating or other wood packaging materials. Examples of plant quarantine pests intercepted include: Anoplophora chinensis, Anoplophora glabripennis, Ips typographus, Hylastes ater, Monochamus sp., Trichoferus campestris and others. The introduction of the Asian long-horned beetle (Anoplophora glabripennis), pine shoot beetle (Tomicus piniperda), emerald ash borer (Agrilus planipennis) and other exotic pests now established in parts of North America can be linked to international shipments containing wood packaging materials. In March 2002, the Interim Commission on Phytosanitary Measures of the International Plant Protection Convention endorsed a standard prescribing uniform regulatory control of wood packaging materials moving in international commerce. This document titled: ISPM No. 15, Guidelines for Regulating Wood Packaging Material in International Trade recognizes the inherent pest risks associated with the international movement of untreated wood packaging materials. Although this standard does not obligate countries to establish regulatory controls, the guideline represents a mechanism by which any country may establish regulatory controls in a manner that is internationally harmonized. This Canadian import policy reflects the guidelines established in ISPM No. 15. This policy does not regulate wood packaging materials originating in the US. As prescribed in ISPM No. 15, Canada has established bilateral phytosanitary measures with the US. Additionally, existing phytosanitary import measures applying to forest products produced in the US provides sufficient phytosanitary protection to Canada. ScopeThis directive is for use by Canadian importers, Canadian customs brokers, CFIA inspectors, Canada Border Services Agency, foreign exporters and national plant protection organizations. ReferencesISPM No. 15, Guidelines for Regulating Wood Packaging Material in International Trade. Rome, 2002, FAO. This directive supersedes D-98-08 (5th Revision), dated June 9 th, 2005. The requirements for the importation of other forest products (including lumber, decorative wood items, etc.) are provided in policy directive D-02-12. Definitions, Abbreviations and AcronymsAll definitions contained within the Plant Protection Act and Plant Protection Regulations; the North American Plant Protection Organization, Glossary of Phytosanitary Terms, August 15, 1999; within the International Standards For Phytosanitary Measures, Glossary of Phytosanitary Terms, ISPM, Pub. No. 5, 1999 and within Amendments to the Glossary of Phytosanitary Terms, October 31, 2000 are included in this document.
1.0 General Requirements1.1 Legislative AuthorityPlant Protection Act, S.C. 1990, c.22 1.2 FeesThe CFIA is charging fees in accordance with the Canadian Food Inspection Agency Fees Notice. For information regarding fees associated with imported product, please contact the Import Service Centres (ISC) at the following phone numbers: Eastern ISC 1-877-493-0468; Central ISC 1-800-835-4486; Western ISC 1-888-732-6222. Anyone requiring other information regarding fees may contact any local CFIA office or Canadian Food Inspection Agency Fees Notice website. 1.3 Regulated PestsNumerous. The following are examples of quarantine pests regulated by Canada: Insects Asian longhorned beetle (Anaplophora glaberpennis) Pathogens Watermark disease of willow (Erwinia salicis) Any other pest associated with wood packaging materials listed in Canada's list of regulated pests. Canada's list of regulated pests may be obtained on the CFIA web site. 1.4 Regulated CommoditiesWood packaging materials constructed from the wood of any plant species that are not manufactured, including dunnage, pallets, spacers, bearers, crating, etc. Note: wood packaging materials used for the transport of lumber are also regulated by this policy. However, logs, wood with bark attached, lumber, wood chips, bark chips, bamboo products, decorative wood items, cones without seed and other forest product imports are regulated by policy directive D-02-12. 1.5 Commodities ExemptAll wood packaging materials constructed entirely from manufactured wood including: dunnage, pallets, spacers, bearers, crating, etc. All wood packaging materials constructed of wood of less than 6mm in thickness or from peeler cores. Wood packing constructed from particles such as: sawdust, wood shavings, wood wool, etc. 1.6 Regulated AreasAll countries other than the continental US. 2.0 Specific Requirements2.1 Entry of Untreated Non-manufactured Wood packaging materialsThe importation or movement in-transit through Canada of untreated non-manufactured wood packaging materials from any area of world excluding the continental US is prohibited. The importation of untreated non-manufactured wood packaging materials originating from areas other than the continental US but transiting through the continental US and entering Canada is prohibited. 2.2 Entry of Treated Non-manufactured Wood packaging materialsA Permit to Import is not required. A Phytosanitary Certificate is not required. A Phytosanitary Certificate may be used as an alternative to the marking systems prescribed below. All non-manufactured wood packaging materials (as defined in section 1.4) may enter Canada provided the material has been officially treated by one of the methods specified in Appendix 1. A logo or mark, officially endorsed by the NPPO of the country from which the wood packaging materials originates must be permanently affixed to each unit of wood packaging materials. More details on the mark are provided in Appendix 2. A Phytosanitary Certificate may be used in lieu of a logo or mark as prescribed above. Replacement wood used in reconditioned wood packaging materials must be treated prior to export by a facility endorsed by the NPPO of the exporting country. The official mark of the facility conducting the treatment of the replacement wood must be affixed to the wood packaging materials. The NPPO of the country from which the wood packaging materials originates must have a certification system in place for the approval and monitoring of facilities producing wood packaging materials to meet international standards. This certification system must ensure that the wood packaging materials or wood used in re-conditioned wood packaging materials are treated in accordance with one of the methods specified in Appendix 1. Facilities must be approved by the NPPO to affix a mark to the treated wood packaging materials. The system of marking must conform to the specifications laid out in Appendix 2. The NPPO must arrange to provide to CFIA on regular basis an updated list of facilities endorsed by the NPPO (e.g. a NPPO may arrange to provide a web-site address where lists are maintained). Importers may determine eligible shippers of wood packaging materials by contacting a local office of the CFIA. Until September 16th, 2005, the CFIA, will permit the entry of wood packaging materials from countries that do not have certification systems in place. The wood packaging materials must have been treated in accordance with the specifications in Appendix 1 and must be accompanied by a document officially endorsed by the NPPO of the country producing the wood packaging materials. The document must identify the treatment that has been applied to the wood packaging materials, the date treatment was applied, the signature and date of the certifying official of the NPPO and the nature of the product accompanying the wood packaging materials. Arrangements regarding the types of documents to be used and the type of endorsement to be applied must be made available to the CFIA prior to any wood packaging materials certified in this manner entering Canada. 3.0 Inspection RequirementsCFIA inspection staff will inspect imports containing wood packaging materials at a rate specified within CFIA operational work plans. Inspectors will verify that wood packaging materials are marked appropriately or accompanied by appropriate certification documents and that the wood packaging material does not contain any pests or signs of living pests. 4.0 Non ComplianceAny regulated material found to be in non-compliance with the import requirements specified above may be ordered removed from Canada. Other penalties applicable under Canadian Food Inspection Agency Acts may be imposed. 4.1 Enforcement during a Phase-in PeriodCanada is harmonizing import legislation with other countries of the North American continent to ensure that trade disruption is minimized. As such, until September 16th 2005, a CFIA inspector may permit the entry of non-compliant wood packaging provided the material is free of pests and diseases and/or signs of pests and diseases. During this transition period only, should signs of pests or symptoms of disease be found, non-compliant wood packaging materials may be permitted to be moved to a facility that safely disposes or processes the wood packaging materials in accordance with the conditions specified in Appendix 3. The CFIA must determine that this movement of non-compliant wood packaging materials is both practically feasible and does not constitute a biological risk to introducing a pest to Canada. Any costs incurred in the disposition of non-compliant wood packaging materials are the responsibility of the person or entity in care and control of the non-compliant wood packaging materials. The facility disposing or processing the non-compliant wood packaging materials must have completed an "Application for Participation in the Non-Compliant Wood packaging materials Disposal or Processing Program" (Appendix 4) and this application must have been approved by an inspector of the CFIA prior to the non-compliant wood packaging materials being granted entry to Canada. Additionally, during this interim period, to ensure that pests associated with untreated ship borne dunnage are controlled, all non-compliant loose wood dunnage must be held on board the marine vessel or at the port area in a container secured against the escape of pests (e.g. a closed disposal bin) until inspected by the CFIA or removed from Canada. Failure to hold dunnage appropriately may result in additional enforcement measures being applied to the person or entity responsible for care and control of the dunnage. Alternatively, the CFIA may permit non-compliant dunnage to enter and be moved to a facility that safely disposes or processes the wood packaging materials in accordance with the conditions specified in Appendix 3. The port facility or parties responsible for the marine vessel offloading the dunnage must obtain a movement certificate ( as specified in Appendix 5) that permits the movement of the dunnage to a CFIA approved disposal or processing facility. The disposal or processing facility must have completed an "Application for Participation in the Non-Compliant Wood Packaging Materials Disposal or Processing Program" (Appendix 4) and this application must have been approved by an inspector of the CFIA prior to the non-compliant wood packaging materials being granted entry to Canada. Port facilities and ship's agents unable to comply with these requirements must ensure that non-compliant loose wood dunnage is not discharged into Canada. Failure to comply with the requirements may result in stringent enforcement measures being applied to the person or entity responsible for care and control of the dunnage, including Canadian agents acting on behalf of the marine vessel, the master or officers of the marine vessel, port authorities or those contracted to handle the dunnage. Any movement of non-compliant wood packaging materials must be authorized by the CFIA on movement certificates issued to the person or entity having care and control of the non-compliant item. Facilities may be permitted to move multiple shipments of non-compliant wood packaging materials on a master movement certificate issued to the facility (a sample is contained in Appendix 5). Movement certificates shall specify the location and the specific conditions by which the wood packaging materials may be moved. 4.2 Enforcement following the Phase-in PeriodFollowing the transition period specified in Section 4.1, any non-compliant wood packaging materials (including loose wood dunnage) entering Canada may be ordered removed from Canada. Additional enforcement measures may be applied to importers or those persons or entities in care and control of non-compliant wood packaging. Permitting the entry of non-compliant wood packaging results in increased risks of pest establishment in Canada and increased uses of pesticide treatments including methyl bromide to remove associated pests. Canada is a signatory to the Montreal Protocol and is taking steps to reduce its overall use of methyl bromide. However, to ensure that wood packaging does not pose a risk for the entry of a pest, the CFIA may order treatment of non-compliant wood packaging prior to it ordered removed from Canada. All costs incurred in the disposition of non-compliant wood packaging are the responsibility of the person or entity in care and control of the non-compliant wood packaging materials at the time of entry to Canada (including port or berthing facilities receiving untreated dunnage). 5.0 List of AppendicesAppendix 1 - Approved Methods of Treatment for Entry into Canada Appendix 1Approved Methods of Treatment for Entry into Canada 1. Heat Treatment All wood packaging materials material must be heated to a minimum internal wood core temperature of 56°C for 30 minutes. Kiln-drying, chemical pressure impregnation, or other treatments may be used as a means of achieving heat treatment provided that the above temperature and time requirements are met. Or 2. Fumigation Wood may be fumigated with methyl bromide at normal atmospheric pressure at the following rates:
The minimum temperature must not be less than 10°C and the minimum exposure time must be at least 24 hours. Monitoring of concentrations must be carried out at a minimum of 2, 4 and 24 hours after application of the fumigant. Or 3 Other Treatment Methods The CFIA may approve other treatment measures, if it can be proven that such measures are effective in minimizing the risk of quarantine pests associated with untreated wood packaging materials. Importers should contact a local office of the CFIA to enquire about the use of other treatments. All costs associated with the verification that an alternative treatment method is effective in precluding pest movement into Canada, must be borne by the importer. Appendix 2Systems Acceptable for the Marking of Wood packaging material that has been treated by one of the methods specified in Appendix 1 and in a manner that is officially endorsed by the NPPO of the country from which the wood packaging materials originates may be permitted entry into Canada provided the wood packaging materials material is marked as follows: 1. The mark must at minimum include:
2. NPPOs or producers may at their discretion add control numbers or other information used for identifying specific lots. Other information may also be included provided it is not confusing, misleading, or deceptive. 3. Markings should be:
4. The colors: red or orange should be avoided. 5. Reconditioned wood packaging materials must be treated and contain the marks of the facility approved to perform the re-treatment. Appendix 3Methods for the Disposal or Processing of 1. Methods for the Disposal or Processing of Non-compliant Wood packaging materials CFIA may permit the movement, disposal or processing of non-compliant wood packaging materials provided that facilities capable of meeting the standards prescribed herein exist to conduct the disposal or processing. All costs incurred in the certification, inspection, monitoring, transport, disposal and/or processing of wood packaging materials must be absorbed by the person or entity in care and control of the wood packaging materials at the time of entry into Canada. The material must be disposed of or processed in a manner that prevents the entry or introduction of pests into Canada. The following methods may be used to dispose or process non-compliant wood packaging materials:
2. Storage of Non-Compliant Wood Packaging Materials While Awaiting Disposal or Processing Any non-compliant wood packaging materials must be, at all times stored in a closed container that is effective in preventing pests from entering into the environment. Storage areas of non-compliant wood packaging materials must be isolated from other domestic wood commodities, material that has already undergone processing and adjacent forested lands by no less than 30 metres. Storage is only permitted until the material can be appropriately disposed or processed as specified in 1 above. An inspector will specify the time limit for storage on a Movement Certificate issued to the person or entity in care and control of the wood packaging material. 3. Transportation of Non-compliant Wood Packaging Materials from Point of Entry to the Site of Disposal or Processing Regardless of the process (described in section 1 of Appendix 3) by which non-compliant wood packaging materials is to be handled, the material may only be moved, by a transporter that is approved by CFIA as specified on a Movement Certificate issued to the person or entity in care and control of the non-compliant wood packaging materials. The wood must be moved in a closed container directly to the site at which disposal or processing is going to take place. 4. Specific Requirements for Disposal or Processing Facilities storing, disposing or processing non-compliant wood packaging materials by the methods described in Section 1 of Appendix 3 must comply with the following specifications:
Appendix 4Application for Participation as a Designated Facility in the Non-Compliant Wood Packaging Materials Disposal and Processing Program
Conditions for the Disposal or Processing of Non-compliant Wood packaging materials:
I, ______________ the owner/person in possession, care, or control of the above named facility have read and understood all the conditions and obligations stated herein by which I may dispose or treat non-compliant wood packaging materials (ship's dunnage, crating or other wood commodities) in accordance with the Non-Compliant Wood Packaging Materials Disposal and Processing Program. Further, I am and shall be responsible for and shall indemnify and save harmless Her Majesty the Queen in Right of Canada, including the Department of Canadian Food Inspection Agency, Her Officers, Servants, Employees, Successors and Assigns, from and against all manners of actions, causes of action, claims, demands, loss, costs, damages, actions or other proceedings by whomsoever made, sustained, brought or prosecuted in any manner based upon, caused by, arising out of, attributable to or with respect to any failure, inadvertent or otherwise, by act or omission, to fully comply with the said conditions and requirements. Dated, __________ in the year ____ at ____, Province of __________ ________________ Verification of Facility Procedures and Processes and Application Approved by:
Appendix 5Sample of Certificate Authorizing Movement of Non-Compliant Wood Packaging |
Top of Page |
Important Notices |