Code of Practice for the Reduction of Dichloromethane Emissions from the Use of Paint Strippers in Commercial Furniture Refinishing and Other Stripping Applications
| TOC | Previous | Next |
2.0 Code of Practice for Miscellaneous Commercial Paint Stripping Facilities
2.1 Applicability
Part 2 of the Code of Practice applies to (i) metal parts paint strippers, (ii) auto body shops, and (iii) building restoration
firms. Not all work practices identified in this section are appropriate for every facility. Each commercial paint stripper
should review the Code and implement those work practices appropriate to its specific situation. The work practices that reduce
the dichloromethane evaporation rate will also serve to minimize paint stripper waste, thus reducing the facility's overall
operating costs.
Several of the work practices identified in this section may apply to facilities that provide commercial paint stripping services
in areas other than those identified above.
![Back to top](/web/20061214010243im_/http://www2.ec.gc.ca/CEPARegistry/graphs/commons/up_arrow.gif)
2.2 General Recommended Work Practices - Commercial Metal Parts Stripping Facilities
Work practices outlined in this section refer to commercial paint strippers that utilize a dip tank to strip the paint from
metal parts. Consider equipping dip tanks or any tanks containing dichloromethane-based paint stripper with dikes and a drain
containment system with sufficient capacity to contain spills or leaks before they evaporate.
![Back to top](/web/20061214010243im_/http://www2.ec.gc.ca/CEPARegistry/graphs/commons/up_arrow.gif)
2.2.1 Evaluate non-dichloromethane-based paint stripping alternatives
Some alternatives to dichloromethane-based paint strippers include thermal stripping, caustic stripping, and media blasting.
Any alternative should be thoroughly evaluated before being employed. All possible benefits and drawbacks of each alternative
should be compared with those of using dichloromethane-based paint strippers before a decision is made.
![Back to top](/web/20061214010243im_/http://www2.ec.gc.ca/CEPARegistry/graphs/commons/up_arrow.gif)
2.2.2 Use paint strippers with lower dichloromethane content when possible
Paint strippers used by metal cleaning facilities generally contain approximately 70-90% dichloromethane. Whenever possible,
it is recommended to use paint strippers with a lower dichloromethane content.
Lower dichloromethane content paint strippers will not in all instances result in reduced dichloromethane emissions. Therefore,
each facility should evaluate its own unique situation and the potential benefits, if any, of using paint strippers with a
lower dichloromethane content.
Lower dichloromethane content paint strippers may not remove the paint from metal parts as rapidly as paint strippers with a
higher dichloromethane content. Therefore, use lower content dichloromethane-based paint strippers when time allows and when
additional quantities of the paint stripper will not be necessary. Additional applications would offset the benefits of using
a lower content dichloromethane-based paint stripper.
![Back to top](/web/20061214010243im_/http://www2.ec.gc.ca/CEPARegistry/graphs/commons/up_arrow.gif)
2.2.3 Clean metal parts prior to stripping
Material caught in crevices may prevent the paint stripper from removing all of the paint from the metal surface. The metal
part may have to be submersed in the dip tank again in order to completely remove all of the paint.
![Back to top](/web/20061214010243im_/http://www2.ec.gc.ca/CEPARegistry/graphs/commons/up_arrow.gif)
2.2.4 Ensure that dip tanks are properly fitted with lids
Dip tanks should be fitted with lids. Keep the lid on the dip tank whenever possible. Lids should be opened only when placing
metal parts in or taking metal parts out of the dip tank. Close the lid on the dip tank immediately after the metal part has
been lowered into or taken out of the dip tank. Keeping the lid closed on the dip tank whenever possible reduces contact
between the paint stripper and the surrounding air, therefore minimizing dichloromethane emissions. Lids for dip tanks may be
constructed of several different materials. Stainless steel is the most desirable, but other metals (i.e., galvanized metals)
may work as well. Plywood or polypropylene lids can be used, but they may retain dichloromethane through absorption or
diffusion and release vapours over time.
Minimize the gap between the lid and the dip tank. Lids for dip tanks may warp due to normal wear and tear. Reducing the gap
between the lid and the dip tank will reduce the level of evaporation and will likely reduce dichloromethane emissions.
Opening and closing the lid to the dip tank generates air disturbances over the surface of the paint stripper in the tank and
results in dichloromethane emissions. Minimize the number of times the tank lid is opened and the duration that the lid remains
open each time. Gently opening and closing the lid could reduce the air disturbance, which should reduce dichloromethane
emissions. To further minimize air disturbance, fit dip tanks with sliding covers.
![Back to top](/web/20061214010243im_/http://www2.ec.gc.ca/CEPARegistry/graphs/commons/up_arrow.gif)
2.2.5 Use water to form a seal on top of the paint stripper when appropriate
A water seal may not be appropriate in all cases, as it may react with the accelerators in the paint stripper, possibly
reducing the efficiency of the paint stripper. Users should confirm compatibility before considering a water seal.
Water seals added on top of the paint stripper in the dip tank form a barrier between the paint stripper and the surrounding air.
The depth of the water seal will depend on the size of the metal parts that the dip tank can accommodate. Facilities should
evaluate the most effective depth for the water seal, but a water layer of 10 cm (4 inches) should properly seal most dip tank
designs.
Introducing metal parts to and removing metal parts from the dip tank will break the water seal and expose the paint stripper
to the surrounding air.
![Back to top](/web/20061214010243im_/http://www2.ec.gc.ca/CEPARegistry/graphs/commons/up_arrow.gif)
2.2.6 Use inert floating balls to form a seal on top of the paint stripper when appropriate
Inert floating balls (e.g., Teflon® balls) that are 1.5-2.5 cm (0.5-1 inch) in diameter can be added to the dip tank so that
they float on top of the paint stripper. The inert balls create a barrier and reduce the surface area of the paint stripper
exposed to the surrounding air. These balls should not absorb paint stripper. Users of this method should ensure that the balls
are compatible with the paint stripper and that they are clean, so that the paint stripper does not adhere to contamination on
the balls. The number of inert balls added to the dip tank will depend on the dimensions of the dip tank.
Inert balls can be accidentally removed when extracting metal parts from the dip tank. It is recommended to clean these balls
immediately and return them to the dip tank.
![Back to top](/web/20061214010243im_/http://www2.ec.gc.ca/CEPARegistry/graphs/commons/up_arrow.gif)
2.2.7 Reduce the surface area of the dip tank
It is recommended to minimize the surface area of the paint stripper in the dip tank as much as possible. Dip tanks come in
various sizes (height, width, length). Using a deeper dip tank that is shorter and narrower will reduce the surface area of
the exposed paint stripper in the dip tank. Minimizing surface area should reduce the amount of paint stripper in contact with
the surrounding air, which will likely minimize emissions.
![Back to top](/web/20061214010243im_/http://www2.ec.gc.ca/CEPARegistry/graphs/commons/up_arrow.gif)
2.2.8 Place metal parts strategically on the rack to be lowered into the dip tank
Avoid placing metal parts on the rack in such a way that they fill with paint stripper. The paint stripper will not be able to
drain from the parts back into the dip tank if the liquid is captured in the metal part. Stand concave metal parts on end to
ensure that the paint stripper drains off when the parts are removed from the dip tank. Hollow metal parts should be placed
with the cavity facing downward so that the paint stripper drains out of the part when it is removed from the dip tank.
![Back to top](/web/20061214010243im_/http://www2.ec.gc.ca/CEPARegistry/graphs/commons/up_arrow.gif)
2.2.9 Let excess paint stripper drip from the metal part
Drain metal parts removed from the dip tank until most of the paint stripper has dripped back into the tank. The time needed
for the paint stripper to drain from the metal part back into the dip tank will depend upon the configuration of the part
being stripped.
The rack holding the metal parts can be lifted out of the dip tank in steps (e.g., a few centimetres or inches at a time).
Removing the rack in steps allows the rack to be agitated or jarred so that more of the paint stripper may be released from
the part and allowed to drip back into the dip tank. Removing the rack in a fluid motion may not recapture as much of the
paint stripper.
![Back to top](/web/20061214010243im_/http://www2.ec.gc.ca/CEPARegistry/graphs/commons/up_arrow.gif)
2.2.10 Evaluate the use of paint strippers that contain a wax additive
Evaluate the use of paint stripping formulations that contain a wax additive. The wax will harden on the top of the paint
stripping formulation when applied. The solidified wax forms a barrier on the exterior of the metal part, which reduces
contact between the dichloromethane in the paint stripper and the surrounding air, thus likely reducing emissions.
![Back to top](/web/20061214010243im_/http://www2.ec.gc.ca/CEPARegistry/graphs/commons/up_arrow.gif)
2.2.11 Maintain the quantity of paint stripper in the dip tank at the lowest possible level
Emissions of dichloromethane can occur when air flows over the paint stripper in an open dip tank and the dichloromethane
evaporates. Keeping as much of the paint stripper as possible in a sealed storage container, and only the minimum amount of
paint stripper necessary in the dip tank, will reduce exposure of the paint stripper to air and will likely reduce emissions
of dichloromethane. In operations with a high rate of air flow, extend the sides of the dip tank vertically. Longer vertical
sides will create a deeper dip tank, which will reduce the amount of surrounding air that contacts the paint stripper.
![Back to top](/web/20061214010243im_/http://www2.ec.gc.ca/CEPARegistry/graphs/commons/up_arrow.gif)
2.2.12 Minimize contact with air when introducing new paint stripper
It is recommended to use a valve and hose system to introduce new paint stripper from the storage container to the dip tank.
Place the end of the hose below the surface of the paint stripping solution. This system will allow the paint stripper to flow
into the dip tank with reduced exposure to the surrounding air. This also minimizes disturbance to the surface of the paint
stripper in the dip tank.
![Back to top](/web/20061214010243im_/http://www2.ec.gc.ca/CEPARegistry/graphs/commons/up_arrow.gif)
2.2.13 Recycle dichloromethane removed in the rinsing process
Use a recycling system to capture dichloromethane where feasible. This recycling system captures dichloromethane that is still
contained on the stripped metal part after removal from the dip tank. After removing metal parts from the dip tank, submerse them
in a rinsing tank instead of spraying them to remove paint chips and excess paint stripper. Since dichloromethane has low water
solubility and is denser than water, excess dichloromethane remaining on the metal part settles to the bottom of the rinsing
tank. The dichloromethane can then be removed from the bottom of the rinsing tank through a valve opening and internally
recycled or sent to a recycler to be reclaimed. Very little, if any, of the dichloromethane evaporates when in the rinsing tank
because of the water barrier in the tank.
Pumps should be used to remove spent paint stripper from the dip tank and into drums without exposing the dichloromethane to the
surrounding air. This pumping system can also be used to remove dichloromethane that has settled to the bottom in the rinsing
tank.
![Back to top](/web/20061214010243im_/http://www2.ec.gc.ca/CEPARegistry/graphs/commons/up_arrow.gif)
2.2.14 Assess the feasibility of venting the air around the dip tank through activated carbon
The air flow above the dip tank can be directed through an activated carbon filter to trap dichloromethane. This work practice
may be more viable for large operations that have high concentrations of dichloromethane in the air surrounding the dip tank.
Properly handle and regularly dispose of the carbon containing dichloromethane.
![Back to top](/web/20061214010243im_/http://www2.ec.gc.ca/CEPARegistry/graphs/commons/up_arrow.gif)
2.3 General Recommended Auto Body Shops
Work practices outlined in this section refer to auto body shops that utilize paint strippers to remove coatings from various
auto body surfaces. This Code of Practice addresses gel- and aerosol-based paint strippers, which are typically used by auto
body shops.
![Back to top](/web/20061214010243im_/http://www2.ec.gc.ca/CEPARegistry/graphs/commons/up_arrow.gif)
2.3.1 Evaluate the use of non-dichloromethane-based alternatives or lower dichloromethane content paint stripping alternatives
Some non-dichloromethane paint stripping alternatives used in auto body shops include sanding and media blasting. Any alternative
should be thoroughly evaluated before being employed. All possible benefits and drawbacks of each alternative should be compared
with those of using dichloromethane-based paint strippers before a decision is made.
Paint strippers used by auto body shops generally contain approximately 70-85% dichloromethane. Whenever applicable, it is
recommended to use paint strippers with a lower dichloromethane content.
It is important to note that lower dichloromethane content paint strippers may not remove the paint from auto body surfaces as
rapidly as paint strippers with a higher dichloromethane content. This may result in the use of larger quantities of lower
content dichloromethane-based paint strippers. Therefore, lower dichloromethane content paint strippers will not always result
in reduced dichloromethane emissions. Each facility should evaluate its own particular situation and the potential benefits and
drawbacks of using paint strippers with a lower dichloromethane content.
![Back to top](/web/20061214010243im_/http://www2.ec.gc.ca/CEPARegistry/graphs/commons/up_arrow.gif)
2.3.2 Sand the surface before applying paint stripper
Sanding the area to be stripped before applying the paint stripper will remove the clearcoat on the auto body surface. Sanding
the clearcoat reduces the quantity of paint stripper required, as fewer coating layers will have to be removed. In addition,
sanding will also allow the paint stripper to penetrate the coating layers more easily.
Sand the surface before applying paint stripper.
It is recommended to make minute scratches with sandpaper in the coatings that are to be stripped so that, when the paint
stripper is applied, the grooves channel the paint stripper. This will reduce the amount of paint stripper wasted on areas
that do not need it.
Hand sanding.
![Back to top](/web/20061214010243im_/http://www2.ec.gc.ca/CEPARegistry/graphs/commons/up_arrow.gif)
2.3.3 Apply masking tape over crevices in the auto body surface
Masking tape can be applied to cover the crevices between the hood and the side of the car to ensure that the paint stripper
does not run under the hood. Masking tape can also ensure that the paint stripper does not flow onto painted sections of the
auto body that are not meant to be stripped.
When stripping large surfaces (e.g., the hood), evaluate the effectiveness of constructing an elevated border to channel the
paint stripper over the desired areas. This would effectively prohibit access to the areas of the automobile that are not to
be stripped, reducing the amount of wasted paint stripper.
![Back to top](/web/20061214010243im_/http://www2.ec.gc.ca/CEPARegistry/graphs/commons/up_arrow.gif)
2.3.4 Brush paint strippers onto the surface in one direction
Paint strippers should not be applied onto the auto body surface in back and forth strokes, as this disturbs the wax seal that
forms on the vehicle surface. Disturbing the wax seal results in exposure of the dichloromethane in the paint stripper to the
surrounding air, which increases the dichloromethane evaporation rate. Air also becomes entrained in the paint stripper,
reducing contact between the dichloromethane and the surface area to be stripped. Excessive brushing will reduce the
effectiveness of the paint stripper.
![Back to top](/web/20061214010243im_/http://www2.ec.gc.ca/CEPARegistry/graphs/commons/up_arrow.gif)
2.3.5 Apply paint strippers to workable surface areas
Paint stripper should be applied in small, workable areas that will allow the paint to be removed before the paint stripper
dries. The size of the workable area will depend on the experience of the individual applying the paint stripper.
The dichloromethane and other solvents in the paint stripper will eventually evaporate and cause the applied paint stripper to
dry out. Should this happen prior to removal of the paint surface, an additional application of paint stripper will be required.
The manufacturer's recommended rate guidelines for paint stripper application should be considered, as they are expected to
minimize the number of occasions on which the paint stripper dries before the paint is scraped from the surface.
![Back to top](/web/20061214010243im_/http://www2.ec.gc.ca/CEPARegistry/graphs/commons/up_arrow.gif)
2.3.6 Leave the paint stripper on the surface for a sufficient length of time
The softening of the coating on the auto body surface signifies that the paint stripper and the coatings are ready to be removed.
Scraping the paint stripper off the vehicle surface prior to this softening reaction risks leaving some of the coating in place.
An additional application of the paint stripper will then be required to remove the remaining coating.
![Back to top](/web/20061214010243im_/http://www2.ec.gc.ca/CEPARegistry/graphs/commons/up_arrow.gif)
2.3.7 Remove paint stripper from storage containers in small quantities
Unused gel-based paint stripper is not typically returned to its storage container once the stripping job is complete. Due to
evaporation of the dichloromethane and other solvents, the returned paint stripper would not have the same properties as the
new paint stripper in the storage container. Therefore, unused paint stripper is typically disposed of. Removing small amounts
from the storage container as required will minimize the quantity of paint stripper wasted.
![Back to top](/web/20061214010243im_/http://www2.ec.gc.ca/CEPARegistry/graphs/commons/up_arrow.gif)
2.3.8 Use gel-based instead of aerosol-based paint strippers whenever possible
Gel-based paint strippers should be applied instead of aerosol-based paint strippers whenever possible.
The size of certain auto body parts (e.g., grill) results in large quantities of the aerosol paint stripper being sprayed onto
areas that are not to be stripped, therefore wasting the product. In these instances, a gel-based paint stripper should be used.
Aerosol-based paint strippers are also generally harder to control than gel-based paint strippers. The fan of the aerosol spray
is difficult to direct, and often some spray enters other areas (e.g., the air). Using a gel-based paint stripper allows better
control and more effective and efficient application of the paint stripper to the desired surface area. Some areas on the auto
body surface (e.g., crevices) may be better suited for aerosol-based paint strippers, since it is difficult to apply the
gel-based paint stripper to these areas.
![Back to top](/web/20061214010243im_/http://www2.ec.gc.ca/CEPARegistry/graphs/commons/up_arrow.gif)
2.3.9 Capture and reuse gel-based paint stripper where applicable
Stripping vertical auto body surfaces or surfaces that are close to the floor may cause gel-based paint stripper to drip onto
the floor. If these drippings are caught on metal/plastic trays, they can be reapplied to the surface being stripped. This
will reduce the quantity of new paint stripper used.
Thicker gel-based paint stripper should be used when stripping vertical auto body surfaces or surfaces close to the floor.
Thicker gel-based paint stripper will be less likely to drip onto the floor and be wasted.
![Back to top](/web/20061214010243im_/http://www2.ec.gc.ca/CEPARegistry/graphs/commons/up_arrow.gif)
2.3.10 Follow manufacturer/supplier's recommendations for optimum application temperature
Some manufacturers of auto body paint strippers have suggested that optimum paint stripping results can be achieved when the
auto body surface is heated to a temperature of 32-40°C before the paint stripper is applied. This is because paint strippers
work faster when applied to a heated surface. However, the paint stripper will dry more quickly if the surface is heated. Only
small areas of the automobile surface should be preheated at a time to ensure that the paint can be removed before the paint
stripper dries. The manufacturer/supplier of the paint stripper used should be contacted to identify the optimum temperature
range. This information may be contained in the application instructions printed on the paint stripper container.
![Back to top](/web/20061214010243im_/http://www2.ec.gc.ca/CEPARegistry/graphs/commons/up_arrow.gif)
2.4 General Recommended Building Restoration
Work practices outlined in this section refer to building restoration firms that utilize paint strippers to remove coatings
from various building surfaces, such as floors, porch railings, and walls. The use of paint strippers to remove graffiti from
building surfaces is another important application. This Code of Practice addresses gel-based paint strippers, which are
typically used by building restoration firms.
![Back to top](/web/20061214010243im_/http://www2.ec.gc.ca/CEPARegistry/graphs/commons/up_arrow.gif)
2.4.1 Evaluate the use of non-dichloromethane-based or lower dichloromethane content paint stripping alternatives
Some non-dichloromethane paint stripping alternatives used by building restoration firms include alcohol-based strippers
and caustic strippers. Any alternative should be thoroughly evaluated before being employed. All possible benefits and
drawbacks of each alternative should be compared with those of using dichloromethane-based paint strippers before a decision
is made.
Paint strippers used by building restoration firms generally contain approximately 35-75% dichloromethane. Whenever applicable,
it is recommended to use paint strippers with a lower dichloromethane content. It is important to note that lower
dichloromethane content paint strippers may not remove the paint from building surfaces as rapidly as paint strippers with a
higher dichloromethane content. This may result in the use of larger quantities of lower content dichloromethane-based paint
strippers. Therefore, lower dichloromethane content paint strippers will not always result in reduced dichloromethane emissions.
Each facility should evaluate its own particular situation and the potential benefits and drawbacks of using paint strippers
with a lower dichloromethane content.
![Back to top](/web/20061214010243im_/http://www2.ec.gc.ca/CEPARegistry/graphs/commons/up_arrow.gif)
2.4.2 Use chemical-resistant sheeting where possible to reduce evaporation rate
Once the paint stripper is applied, the surface in question should be covered with chemical-resistant sheeting (e.g.,
polypropylene, nylon). Tape down the corners of the chemical-resistant sheeting. The use of protective sheeting will extend the
paint stripper drying time and help the stripper to penetrate the coatings. This will increase the effectiveness of the paint
stripper, so that more paint is stripped off and less additional paint stripper will be required to finish the job.
![Back to top](/web/20061214010243im_/http://www2.ec.gc.ca/CEPARegistry/graphs/commons/up_arrow.gif)
2.4.3 Distribute paint stripper evenly over the surface area to be stripped
Applying an even coat of paint stripper ensures that the entire surface receives the same quantity of paint stripper and that
no area will dry more quickly than others.
![Back to top](/web/20061214010243im_/http://www2.ec.gc.ca/CEPARegistry/graphs/commons/up_arrow.gif)
2.4.4 Perform a test with the paint stripper on the surface area to be stripped
It is recommended to test the surface to be stripped to determine the quantity of paint stripper that will be required to remove
the coatings. When performing a test, ensure that the test area reflects the entire surface in question. Non-dichloromethane-based
paint strippers can also be tested to determine if they would work on the surface being stripped. Testing the surface area will
determine the optimum amount of paint stripper to be applied to remove the coatings. This should reduce the need for application of
additional paint stripper. If alternative paint strippers prove to be effective in the test, the use of the dichloromethane-based
paint stripper can be avoided.
If there are other areas of the project in which different or additional coatings are suspected, then a test zone of that area
would also be warranted.
![Back to top](/web/20061214010243im_/http://www2.ec.gc.ca/CEPARegistry/graphs/commons/up_arrow.gif)
2.4.5 Apply paint strippers to workable surface areas
Paint stripper should be applied in small, workable areas that will allow the paint to be removed before the paint stripper
dries. The dichloromethane and other solvents in the paint stripper will eventually evaporate and cause the applied stripper to dry.
Should this occur before the paint surface is removed, an additional application of paint stripper will be required.
Applying the manufacturer's recommended amount will likely minimize the number of occasions on which the paint stripper dries
before the paint is removed from the surface.
![Back to top](/web/20061214010243im_/http://www2.ec.gc.ca/CEPARegistry/graphs/commons/up_arrow.gif)
2.4.6 Maintain optimum working conditions for the paint stripper
Dichloromethane dries more quickly if the surface being stripped is heated - for instance, if it is in direct sunlight. Paint
strippers dry more slowly and maintain their effectiveness for longer periods on cooler and shaded surfaces. When applying
dichloromethane-based paint strippers to large areas (as in building restoration), the surface should be cool and shaded to
prevent the paint stripper from drying before it can be removed. The optimum ambient temperature when working with paint
strippers is between 13°C and 24°C.
![Back to top](/web/20061214010243im_/http://www2.ec.gc.ca/CEPARegistry/graphs/commons/up_arrow.gif)
2.5 Recommendations for Paint Stripper Handling and Storage
Storage and handling information is communicated on the Material Safety Data Sheets. Refer to these sheets for further instructions.
- Ship paint stripper in closed, airtight containers.
- It is recommended to keep the lids on paint stripper containers tightly closed at all times. Refasten paint stripper container
lids immediately after paint stripper is removed from the container.
- Paint stripper containers should be stored in a cool, dry, well-ventilated location. Exposure to high temperatures or to the sun
may cause paint stripper containers to leak or swell.
- Try to remove as much of the paint stripper from its storage container as possible before disposing of the storage container.
- When filling smaller vessels from the larger paint stripper storage container, keep the tap near, if not in, the entry hole to
reduce exposure to the surrounding air.
- All handling and storage activities should be in compliance with local regulations, such as provincial fire codes, etc.
- Consider equipping storage tanks containing dichloromethane-based paint stripper with dikes and a drain containment system with
sufficient capacity to contain spills or leaks before they evaporate.
![Back to top](/web/20061214010243im_/http://www2.ec.gc.ca/CEPARegistry/graphs/commons/up_arrow.gif)
2.6 Recommendations for Waste Handling and Disposal
Hazardous waste disposal information is communicated on the Material Safety Data Sheets. Refer to these sheets for further instruction.
- It is recommended to dispose of empty, non-returnable containers immediately using an approved method. Treat the
containers as waste or hazardous waste as appropriate. Local solid waste authorities can usually assist with
this.
- All waste handling and disposal should be in compliance with local, provincial, aboriginal, territorial, and federal regulations,
such as the Transportation of Dangerous Goods Act. Note that generators of hazardous waste may require registration with provincial
or territorial authorities.
- If a container is to be used to accumulate material for recycling or waste disposal, it should be stored with lids and all other
openings tightly sealed after every addition.
- Ship waste or recyclable materials in closed, airtight containers.
- After the paint stripping process, collect materials soaked with paint stripper and transfer them immediately to the designated waste
storage container. Dispose of this waste through a government authorized waste disposal or processing company. Suppliers of paint
stripper may have a collection service for contaminated paint stripper. Contact the local county, municipal, provincial or territorial government authority for instructions on disposal.
- It may be possible to wipe the stripped surface down with a damp (with water or lacquer thinner) cloth, steel wool pad, or stiff
bristle brush instead of hosing down the surface. This will avoid the introduction of paint stripper residue and dichloromethane
into the municipal wastewater system. Place the used scrubbing materials (e.g., brush, cloth, etc.) in a sealed storage container
after use, and dispose of them according to the environmental requirements of the local municipal authority.
![Back to top](/web/20061214010243im_/http://www2.ec.gc.ca/CEPARegistry/graphs/commons/up_arrow.gif)
2.7 Recommendations for Record-keeping
The information required in this section should be kept for three years to track paint stripper use and to help develop an
internal dichloromethane emission reduction system.
- It is recommended to record specific actions implemented to reduce the quantity of paint stripper used or the quantity of
dichloromethane emissions. These actions may be contained in this Code of Practice or may be developed by the facility. Also
record the date on which these actions were initiated at the paint stripping facility.
- It is also recommended to record the quantity of dichloromethane, as contained in paint strippers, used per year. Commercial
paint strippers should ask the paint stripper manufacturer or their supplier to track the facility's annual paint stripper
purchases as well as the dichloromethane content of that product. Running totals on invoices may be provided, indicating the
total paint stripper and dichloromethane usage for the year to date.
Should the manufacturer or supplier be unable to provide a running total of annual dichloromethane consumption, this amount may
be estimated. To determine the quantity of dichloromethane used per year, keep records on the quantity (volume) of
dichloromethane-based paint stripper purchased per year and its percent dichloromethane content. Product information sheets for
the paint stripper will contain a range of the dichloromethane content in the paint stripper (e.g., 3-7%, 5-10%, 40-70%) or the
actual content (e.g., 80%). The percent dichloromethane content may be expressed on a weight basis or a volume basis. Use the
actual or an estimated content level to calculate total dichloromethane consumption for the year.
For instance, 10 drums, each 205 litres, of dichloromethane-based paint stripper were purchased during the year. This gives 10 ×
205 = 2050 litres of paint stripper purchased for the year. If the average dichloromethane content of the paint stripper is 70%
by volume, 2050 litres × 0.70 = 1435 litres of dichloromethane were purchased during the year. If the average dichloromethane
content of the paint stripper is 70% by weight, first convert the 2050 litres of paint stripper to mass using the density of the
formulation (found on the Material Safety Data Sheet). Then multiply that mass by 0.70 to obtain the total mass of dichloromethane
purchased for the year. To convert the mass of dichloromethane into volume, divide the mass (in kilograms) by the density of
dichloromethane (1.32 kilograms per litre).
Record the quantities of dichloromethane-containing waste along with the details of the waste disposal and/or recycling company
and method of disposal or recovery. Subtract this quantity from purchases to estimate releases.
If the ownership of a commercial paint stripping operation is transferred, it is recommended to transfer records related to paint
stripper use and reduction measures implemented to the new owner along with a copy of this Code.
![Back to top](/web/20061214010243im_/http://www2.ec.gc.ca/CEPARegistry/graphs/commons/up_arrow.gif)
2.8 Recommended Training
- It is recommended to train individuals responsible for paint stripping to use the specific work practices contained in this
Code of Practice. In addition to an initial training, give all operators an annual refresher course. The training provided
should teach the skills necessary to implement the work practices in this Code of Practice.
- Train the individuals responsible for paint stripping to implement the recommended paint stripper application instructions
provided by the manufacturer.
- Employers should ensure that employees are familiar with Material Safety Data Sheets, other health and safety documents, and
any paint stripper product literature provided by suppliers. If the provided product literature does not enable the employer
to accurately determine the quantity of dichloromethane in the paint stripper, the employer may wish to contact the supplier
for a more precise concentration.
- Train all employees involved in the handling and use of paint strippers to use the appropriate personal protective and emergency
equipment.
![Back to top](/web/20061214010243im_/http://www2.ec.gc.ca/CEPARegistry/graphs/commons/up_arrow.gif)
|