|
|
Effective Date: November 14, 2007
Mandatory Compliance Date: May 14, 2008
Disclaimer
The documents in HTML format that are provided on this Web site have
been prepared for use as a ready reference and do not have legal force
or effect. A Portable Document Format (PDF) version is provided for the
purposes of interpretation and application. The PDF version may be viewed
using version 3.0 or higher of the Adobe® Acrobat Reader, which may
be downloaded free of charge by visiting the Adobe®
Web site.
|
|
Technical Standards Document
Number 114, Revision 0
Theft Protection and Rollaway Prevention
As defined by section
12 of the Motor Vehicle Safety Act, a Technical Standards
Document (TSD) is a document that reproduces an enactment of a foreign
government (e.g. a Federal Motor Vehicle Safety Standard issued by the
U.S. National Highway Traffic Safety Administration). According to the
Act, the Motor Vehicle Safety Regulations may alter or override
some provisions contained in a TSD or specify additional requirements;
consequently, it is advisable to read a TSD in conjunction with the Act
and its counterpart Regulation. As a guide, where the corresponding Regulation
contains additional requirements, footnotes indicate the amending subsection
number.
TSDs are revised from time to time in order to incorporate amendments
made to the reference document, at which time a Notice of Revision is
published in the Canada Gazette, Part I. All TSDs are assigned
a revision number, with "Revision 0" designating the original version.
Identification of Changes
In order to facilitate the incorporation of a TSD, certain non-technical
changes may be made to the foreign enactment. These may include the deletion
of words, phrases, figures, or sections that do not apply under the Act
or Regulations, the conversion of imperial to metric units, the deletion
of superseded dates, and minor changes of an editorial nature. Additions
are underlined, and provisions that do not apply are stroked
through. Where an entire section has been deleted, it is replaced
by: "[CONTENT DELETED]". Changes are also made where there is
a reporting requirement or reference in the foreign enactment that does
not apply in Canada. For example, the name and address of the U.S. Department
of Transportation are replaced by those of the Department of Transport.
Effective Date and Mandatory Compliance Date
Compliance with the requirements of a TSD that is being introduced
for the first time is not mandatory until six months after publication
in the Canada Gazette, Part II, of the Regulations that incorporate
the TSD. In the case of a revision, compliance becomes mandatory six months
after publication of the Notice of revision in the Canada Gazette,
Part I, as long as the requirements of the previous version continue to
be met. Voluntary compliance is permitted as of the Effective Date of
the TSD.
Official Version of Technical Standards Documents
Technical Standards Documents may be consulted electronically in both
HTML and Portable Document Format (PDF) on the Department of Transports
Web site at www.tc.gc.ca/RoadSafety/mvstm_tsd/index_e.htm.
The PDF version is a replica of the TSD as published by the Department
and is to be used for the purposes of legal interpretation and application.
The HTML version is provided for information purposes only.
(Original signed by)
Director, Standards Research and Development
for the Minister of Transport,
Infrastructure and Communities
Ottawa, Ontario
Technical Standards Document
Number 114, Revision 0
THEFT PROTECTION AND ROLLAWAY PREVENTION
The text of this document is based on Federal Motor Vehicle Safety
Standard No. 114, Theft Protection and Rollaway Prevention,
as published in the U.S. Code of Federal Regulations, Title
49, Part 571, revised as of October 1, 2006.
S1. Scope
This Technical Standards Document (TSD) standard
specifies vehicle performance requirements intended to reduce the incidence
of crashes resulting from theft and accidental rollaway of motor vehicles.
S2. Purpose
The purpose of this TSD standard is to decrease
the likelihood that a vehicle is stolen, or accidentally set in motion.
|
|
S3. Application
[CONTENT DELETED] For applicability, see Schedule
III and section
114(1) of Schedule IV to the Motor Vehicle Safety Regulations.
S4. Definitions
Combination means a variation of the key that permits
the starting system of a particular vehicle to be operated. (Combinaison)
Key means a physical device or an electronic code which,
when inserted into the starting system (by physical or electronic means),
enables the vehicle operator to activate the engine or motor. (Clé)
1 Open-body type vehicle
means a vehicle having no occupant compartment doors or a vehicle
having readily detachable occupant compartment doors. (Véhicule
de type ouvert)
Starting system means the vehicle system used in conjunction
with the key to activate the engine or motor. (Circuit de démarrage)
Vehicle type, as used in S5.1.2, refers to a vehicle
mentioned in subsection 114(1) of Schedule IV to the Motor Vehicle
Safety Regulations passenger car, truck or multipurpose
passenger vehicle, as those terms are defined in 49 CFR 571.3.
(Type de véhicule)
|
|
S5. Requirements2
Each vehicle subject to this TSD standard must
meet the requirements of S5.1 and S5.2. Open-body type vehicles are not
required to comply with S5.1.3.
S5.1 Theft Protection
S5.1.1 Each vehicle must have a starting system which,
whenever the key is removed from the starting system, prevents:
(a) The normal activation of the vehicle’s engine or motor; and
(b) Either steering, or forward self-mobility, of the vehicle, or both.
S5.1.2 For each vehicle type manufactured by a manufacturer,
the manufacturer must provide at least 1,000 unique key combinations,
or a number equal to the total number of the vehicles of that type manufactured
by the manufacturer, whichever is less. The same combinations may be used
for more than one vehicle type.
S5.1.3 Except as specified below, an audible warning
to the vehicle operator must be activated whenever the key is in the starting
system and the door located closest to the driver’s designated seating
position is opened. An audible warning to the vehicle operator need not
activate:
(a) After the key has been inserted into the starting system, and before
the driver takes further action; or
(b) If the key is in the starting system in a manner or position that
allows the engine or motor to be started or to continue operating; or
(c) For mechanical keys and starting systems, after the key has been
withdrawn to a position from which it may not be turned.
S5.1.4 If a vehicle is equipped with a transmission
with a “park” position, the means for deactivating the vehicle’s
engine or motor must not activate any device installed pursuant to S5.1.1(b),
unless the transmission is locked in the “park” position.
S5.2 Rollaway Prevention in Vehicles Equipped
With Transmissions With a “Park” Position
S5.2.1 Except as specified in S5.2.3, the starting system
required by S5.1 must prevent key removal when tested according to the
procedures in S6, unless the transmission or gear selection control is
locked in “park” or becomes locked in “park” as
a direct result of key removal.
S5.2.2 Except as specified in S5.2.4, the vehicle must
be designed such that the transmission or gear selection control cannot
move from the “park” position, unless the key is in the starting
system.
S5.2.3 Key Removal Override Option
At the option of the manufacturer, the key may be removed from the starting
system without the transmission or gear selection control in the “park”
position under one of the following conditions:
(a) In the event of electrical failure, including battery discharge,
the vehicle may permit key removal from the starting system without the
transmission or gear selection control locked in the “park”
position; or
(b) Provided that steering or self-mobility is prevented, the vehicle may
have a device by which the user can remove the key from the starting system
without the transmission or gear selection control locked in “park”.
This device must require:
(i) The use of a tool, and
(ii) Simultaneous activation of the device and removal of the key; or
(c) Provided that steering or self-mobility is prevented, the vehicle may
have a device by which the user can remove the key from the starting system
without the transmission or gear selection control locked in “park”.
This device must be covered by an opaque surface which, when installed:
(i) Prevents sight of and use of the device, and
(ii) Can be removed only by using a screwdriver or other tool.
S5.2.4 Gear Selection Control Override Option
The vehicle may have a device by which the user can move the gear selection
control from “park” after the key has been removed from the
starting system. This device must be operable by one of the three options
below:
(a) By use of the key; or
(b) By a means other than the key, provided steering or forward self-mobility
is prevented when the key is removed from the starting system. Such a
means must require:
(i) The use of a tool, and
(ii) Simultaneous activation of this means and movement of the gear selection
control from “park”; or
(c) By a means other than the key, provided steering or forward self-mobility
is prevented when the key is removed from the starting system. This device
must be covered by an opaque surface which, when installed:
(i) Prevents sight of and use of the device, and
(ii) Can be removed only by using a screwdriver or other tool.
S5.2.5 When tested in accordance with S6.2.2, each vehicle
must not move more than 150 mm on a 10-percent grade when the gear selection
control is locked in “park”. |
|
|
|
S6. Compliance
Test Procedure for Vehicles With Transmissions With a “Park”
Position
S6.1 Test Conditions
S6.1.1 The vehicle shall be tested at curb mass
weight plus 91 kg (including the driver).
S6.1.2 Except where specified otherwise, the test
surface shall be level.
S6.2 Test Procedure
|
|
S6.2.1
| (a) Activate the starting system using the
key.
(b) Move the gear selection control to any gear selection position or
any other position where it will remain without assistance, including
a position between any detent positions, except for the “park”
position.
(c) Attempt to remove the key in each gear selection position.
|
|
S6.2.2
| (a) Drive the vehicle forward up a 10-percent
grade and stop it with the service brakes.
(b) Apply the parking brake (if present).
(c) Move the gear selection control to “park”.
(d) Note the vehicle position.
(e) Release the parking brake. Release the service brakes.
(f) Remove the key.
(g) Verify that the gear selection control or transmission is locked
in “park”.
(h) Verify that the vehicle, at rest, has moved no more than 150 mm
from the position noted prior to release of the brakes.
|
|
S6.2.3
| (a) Drive the vehicle forward down a 10-percent
grade and stop it with the service brakes.
(b) Apply the parking brake (if present).
(c) Move the gear selection control to “park”.
(d) Note the vehicle position.
(e) Release the parking brake. Release the service brakes.
(f) Remove the key.
(g) Verify that the gear selection control or transmission is locked
in “park”.
(h) Verify that the vehicle, at rest, has moved no more than 150 mm
from the position noted prior to release of the brakes.
|
ENDNOTES:
1 Please see subsection
2(1) of the Motor Vehicle Safety Regulations (MVSR) for the
applicable definition.
2 Please see subsections
114(3) to (8) of the MVSR for additional requirements.
|