|
![Skip all menus (access key: 2)](/web/20071214060302im_/http://www.tc.gc.ca/images/18px.gif) |
Disclaimer: These documents are not the official versions (more).
Standard 116
Motor Vehicle Brake Fluids (Standard 116)
116. (1) The hydraulic brake system of a vehicle shall
contain brake fluid that conforms to the requirements of Technical Standards
Document No. 116, Motor Vehicle Brake Fluids (TSD 116), as amended from
time to time.
(2) A reference in TSD 116 to a standard published by ASTM that is set out in
column 1 of the table to this subsection may be read as a reference to the
standard set out opposite that standard in column 2 of the table.
TABLE
Item |
Column 1 |
Column 2 |
1. |
ASTM D 445 65, Viscosity of Transparent and Opaque Liquids
(Kinematic and Dynamic Viscosities) |
ASTM D 445 06, Standard Test Method for Kinematic Viscosity of
Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity) |
2. |
ASTM D 1121 67, Standard Method of Test for Reserve Alkalinity
of Engine Antifreezes and Antirusts |
ASTM D 1287 91 (reapproved in 2002), Standard Test Method for
pH of Engine Coolants and Antirusts |
3. |
ASTM D 1123 59, Standard Method of Test for Water in
Concentrated Engine Antifreezes by the Iodine Reagent Method |
ASTM D 1123 99 (reapproved in 2003), Standard Test Methods for
Water in Engine Coolant Concentrate by the Karl Fischer Reagent Method |
4. |
ASTM D 1193 70, Standard Specifications for Reagent Water |
ASTM D 1193 99ε1, Standard Specification for
Reagent Water |
5. |
ASTM D 1415 68, Standard Method of Test for International
Hardness of Vulcanized Natural and Synthetic Rubbers |
ASTM D 1415 06, Standard Test Method for Rubber Property
International Hardness |
6. |
ASTM D 2515 66, Standard Specification for Kinematic Glass
Viscometers |
ASTM D 446 06, Standard Specifications and Operating
Instructions for Glass Capillary Kinematic Viscometers |
7. |
ASTM E 1 68, Specifications for ASTM Thermometers |
ASTM E 1 05, Standard Specification for ASTM Liquid-in-Glass
Thermometers |
8. |
ASTM E 77 66, Verification and Calibration of Liquid-in-Glass
Thermometers |
ASTM E 77 98, (reapproved in 2003), Standard Test Method for
Inspection and Verification of Thermometers |
9. |
ASTM E 298 68, Standard Methods for Assay of Organic Peroxides |
ASTM E 298 01, Standard Test Methods for Assay of Organic
Peroxides |
(3) This section expires on January 1, 2012.
Established by the CONSOLIDATED REGULATIONS OF CANADA, 1978.
amended by
SOR/79-940 6 December, 1979 pursuant to sections 4 and 7 of the Motor Vehicle Safety
Act
Section 118 of Schedule IV is renumbered as section 116.
SOR/93-561 9 December, 1993 pursuant to sections 4 and 7 of the Motor Vehicle Safety
Act
The heading preceding section 116 of Schedule IV; subsection 116(2) of Schedule IV
preceding paragraph (a); subsection 116(3) of Schedule IV preceding paragraph (a);
subsection 116(4) of Schedule IV preceding paragraph (a); subsection 116(5) of Schedule IV
preceding paragraph (a); paragraph 116(5)(c) of Schedule IV; subparagraphs 116(k)(iii) to
(vi) of Schedule IV; subsection 116(6) of Schedule IV preceding paragraph (a); section 116
of Schedule IV by adding sections 116(7) and 116(8).
SOR/2007-180 July 31, 2007 pursuant to section 5 and subsection 11(1) of the
Motor Vehicle Safety Act comes into force August 22, 2007.
Section 116 of Schedule IV and the heading before it are replaced.
|