|
|
Issued: April 15, 1996
Revised: August 23, 1996
Disclaimer
The documents in HTML format that are provided on this Web site have
been prepared for use as a ready reference and do not have legal force
or effect. A Portable Document Format (PDF) version is provided for the
purposes of interpretation and application. The PDF version may be viewed
using version 3.0 or higher of the Adobe® Acrobat Reader, which may
be downloaded free of charge by visiting the Adobe®
Web site.
|
|
TECHNICAL STANDARDS DOCUMENT
Number 206
Door Locks and Door Retention Components
This Technical Standards Document reproduces the content of Federal Motor
Vehicle Safety Standard No. 206, "Door Locks and Door Retention Components",
issued by the National Highway Traffic Safety Administration of the United
States Department of Transportation. The general requirements governing
Technical Standards Documents (TSD) are set out in section
12 of the Motor Vehicle Safety Act, which allows for
the use of a TSD to incorporate enactments by a foreign government. Because
the requirements of the Regulations may alter or override some provisions
or specify additional requirements, this Document should be read in conjunction
with the Motor Vehicle Safety Act and section
206 of the Motor Vehicle Safety Regulations. As
a guide, the subsection of the Regulations that alters or limits a TSD
provision is indicated in the margin by the number within parentheses.
Amendments to this TSD will be made from time to time to incorporate revisions
made to the reference document, and a Notice of Revision announcing an
amendment will be published in the Canada Gazette Part I. The revised
TSD will come into force six months after publication of the Notice.
Certain non-technical changes have been made to the U.S. standard by
the Department of Transport. These include the deletion of items that
do not apply under the Motor Vehicle Safety Act, minor changes
of an editorial nature, and the correction of a conversion error in S5.5.
Additions have been underlined, and provisions that do not apply
have been stroked-through. One section has been deleted
completely and marked "[CONTENT DELETED]".
Identification of Changes
In order to facilitate the incorporation of a TSD, certain non-technical
changes may be made to the foreign enactment. These may include the deletion
of words, phrases, figures, or sections that do not apply under the Act
or Regulations, the conversion of imperial to metric units, the deletion
of superseded dates, and minor changes of an editorial nature. Additions
are underlined, and provisions that do not apply are stroked
through. Where an entire section has been deleted, it is replaced
by: "[CONTENT DELETED]". Changes are also made where there is
a reporting requirement or reference in the foreign enactment that does
not apply in Canada. For example, the name and address of the U.S. Department
of Transportation are replaced by those of the Department of Transport.
Effective Dates
The original version of a TSD comes into effect on the date that the
regulation in which it is first incorporated by reference is published
in the Canada Gazette Part II. Subsequent revisions of a TSD come
into effect on the date of publication of the Notice of Revision in the
Canada Gazette Part I. The Effective Date is that of the publication
of the final amendment or the notice of revision in the Canada Gazette.
Compliance with the requirements of a newly issued TSD is not mandatory
until six months following the effective date, during which time it is
permissible to continue to comply with the requirements of the previous
Regulation or TSD. Manufacturers and importers must comply with the requirements
of a newly issued TSD as of the Mandatory Compliance Date.
Official Version of Technical Standards Documents
Technical Standards Documents may be consulted electronically in both
HTML and Portable Document Format (PDF) on the Department of Transports
Web site at www.tc.gc.ca/RoadSafety/mvstm_tsd/index_e.htm.
The PDF version is a replica of the TSD as published by the Department
and is to be used for the purposes of legal interpretation and application.
The HTML version is provided for information purposes only.
(Original signed by)
Director, Motor Vehicle Standards and Research
for the Minister of Transport
Ottawa, Ontario
Technical Standards Document
Number 206
DOOR LOCKS AND DOOR RETENTION COMPONENTS
(Ce document est aussi disponible en français.)
The text of this document is based on the U.S. Code of Federal Regulations,
Title 49, part 571, Federal Motor Vehicle Safety Standard No. 206,
Door Locks and Door Retention Components, and subsequent amendments,
revised as of October 1, 1992, up to and including the Final Rule, Docket
94-70, Notice 4, published in the Federal Register on July 31,
1996 (Vol. 61, No. 148, p. 39907).
This Technical Standards Document (TSD) standard
specifies requirements for door locks and door retention components, including
latches, hinges, and other supporting means, to minimize the likelihood
of occupants being thrown from a vehicle as a result of impact. |
(1)*
|
[CONTENT DELETED] For applicability, also see Schedule
III of the Motor Vehicle Safety Regulations.
Auxiliary door latch means a latch or latches, other than the
primary latch or latches, fitted to a back door or door system that is
equipped with more than one latch. (Gâche auxiliaire)
Back door means a door or door system on the back end of a motor
vehicle through which passengers can enter or depart the vehicle,
or cargo can be loaded or unloaded; but does not include:
(a) a trunk lid; or
(b) a door or window that is composed entirely of glazing material
and whose latches and/or hinges are attached directly to the glazing
material. (Porte arrière)
Cargo-type door means a door designed primarily to accommodate
cargo loading including, but not limited to, a two-part door that latches
to itself. (Porte de chargement)
Fork-bolt means the part of the door latch that engages the striker
when in a latched position. (Gorge)
Fork-bolt opening means the direction opposite to that in which
the striker enters to engage the fork-bolt. (Ouverture de la gorge)
Primary door latch means, with respect to a back door or back
door system, the latch or latches equipped with both the fully latched
position and the secondary latched position. (Gâche primaire)
Side front door means a door that, in a side view, has 50 percent
or more of its opening area forward of the rearmost point on the driver's
seatback, when the driver's seat is adjusted to its most vertical and
rearward position. (Porte latérale avant)
Side rear door means a door that, in a side view, has more than
50 percent of its opening area to the rear of the rearmost point on the
driver's seatback, when the driver's seat is adjusted to its most vertical
and rearward position. (Porte latérale arrière)
Trunk lid means a movable body panel that provides access from
outside the vehicle to a space wholly partitioned from the occupant compartment
by a permanently attached partition or a fixed or fold-down seat back.
(Couvercle du coffre)
(a) Components on side doors. Components on any side door that
leads directly into a compartment that contains one or more seating
accommodations shall conform to this standard.
(b) Components on back doors. Components on any back door of
a passenger car or multipurpose passenger vehicle with a gross vehicle
weight rating (GVWR) of 4 536 kilograms (10,000 pounds) or
less that leads directly into a compartment that contains one or more
seating accommodations shall conform to this standard, subject to the
following compliance schedule:
|
(2)
|
(1)(i) For those affected passenger cars and multipurpose passenger
vehicles manufactured on or after September 1, 1997, and before September
1, 1998, the amount of such vehicles complying with this standard shall
be not less than 60 percent of the combined total production of passenger
cars and multipurpose passenger vehicles, based on:
(A) The manufacturer's average annual production of such vehicles
manufactured on or after September 1, 1996, and before September
1, 1998; or
(B) The manufacturer's production of such vehicles on or after
September 1, 1997, and before September 1, 1998.
(ii) For calculating average annual production of affected passenger
cars and multipurpose passenger vehicles for each manufacturer and
the number of such vehicles manufactured by each manufacturer, a vehicle
produced by more than one manufacturer shall be attributed to a single
manufacturer as follows:
(A) A vehicle that is imported shall be attributed to the importer;
(B) A vehicle manufactured in the United States by
more than one manufacturer, one of which also markets the vehicle,
shall be attributed to the manufacturer that markets the vehicle;
(C) A vehicle produced by more than one manufacturer shall be attributed
to any one of the vehicle's manufacturers specified by an express
written contract between the manufacturer so specified and the manufacturer
to which the vehicle would otherwise be attributed under paragraph
(b)(1)(ii) (A) or (B) of this section.
(2) Components on the back doors of affected passenger cars and multipurpose
passenger vehicles manufactured on and after September 1, 1998, shall
conform to all applicable requirements of this standard.
(c) Components on folding doors, roll-up doors, doors that are designed
to be easily attached to or detached from motor vehicles manufactured
for operation without doors, and doors that are equipped with wheelchair
lifts and that are linked to an alarm system consisting of either a
flashing visible signal located in the driver's compartment or an alarm
audible to the driver that is activated when the door is open, need
not conform to this standard.
(d) A particular latch or hinge assembly utilized as a test specimen
need not meet further requirements after having been subjected to and
having met any one of the requirements of S4 or S5.1 through S5.4.
S4.1.1 Door Latches. Each door latch and striker assembly shall
be provided with two positions consisting of:
(a) A fully latched position; and
(b) A secondary latched position.
S4.1.1.1 Longitudinal Load. The door latch and striker assembly,
when in the fully latched position, shall not separate when a longitudinal
load of 11 000 Newtons (2500 pounds) is applied. When in
the secondary latched position, the door latch and striker assembly shall
not separate when a longitudinal load of 4 450 Newtons (1000 pounds)
is applied.
S4.1.1.2 Transverse Load. The door latch and striker assembly,
when in the fully latched position, shall not separate when a transverse
load of 8 900 Newtons (2000 pounds) is applied. When in the
secondary latched position, the door latch and striker assembly shall
not separate when a transverse load of 4 450 Newtons (1000 pounds)
is applied.
S4.1.1.3 Inertia Load. The door latch shall not disengage from
the fully latched position when a longitudinal or transverse inertia load
of 30 g is applied to the door latch system (including the latch
and its actuating mechanism with the locking mechanism disengaged).
S4.1.2 Door Hinges. Each door hinge system shall support the
door and shall not separate when a longitudinal load of 11 000 Newtons
(2500 pounds) is applied. Similarly, each door hinge system shall not
separate when a transverse load of 8 900 Newtons (2000 pounds)
is applied.
S4.1.3 Door Locks. Each door shall be equipped with a locking
mechanism with an operating means in the interior of the vehicle.
S4.1.3.1 Side Front Door Locks. When the locking mechanism is
engaged, the outside door handle or other outside latch release control
shall be inoperative.
S4.1.3.2 Side Rear Door Locks. In passenger cars and multipurpose
passenger vehicles, when the locking mechanism is engaged, both the outside
and inside door handles or other latch release controls shall be inoperative.
S4.2.1 Door Latches
S4.2.1.1 Longitudinal Load. Each latch system, when in the latched
position, shall not separate when a longitudinal load of 11 000 Newtons
(2500 pounds) is applied.
S4.2.1.2 Transverse Load. Each latch system, when in the latched
position, shall not separate when a transverse load of 8 900 Newtons
(2000 pounds) is applied. When more than one latch system is used
on a single door, the load requirement may be divided among the total
number of latch systems.
S4.2.2 Door Hinges. Each door hinge system shall support the door
and shall not separate when a longitudinal load of 11 000 Newtons
(2500 pounds) is applied, and when a transverse load of 8 900 Newtons
(2000 pounds) is applied.
The track and slide combination or other supporting means for each sliding
door shall not separate when a total transverse load of 17 800 Newtons
(4000 pounds) is applied, with the door in the closed position.
S4.4.1 Door Latches. Each back door system shall be equipped with
at least one primary latch and striker assembly.
S4.4.1.1 Load Test One. The primary door latch and striker assembly,
when in the fully latched position, shall not separate when a load of
11 000 Newtons (2500 pounds) is applied in the direction
perpendicular to the face of the latch (corresponding to the longitudinal
load test for side door latches) such that the latch and the striker anchorage
are not compressed against each other. When in the secondary latched position,
the primary latch and striker assembly shall not separate when a load
of 4 450 Newtons (1000 pounds) is applied in the same direction.
S4.4.1.2 Load Test Two. The primary door latch and striker assembly,
when in the fully latched position, shall not separate when a load of
8 900 Newtons (2000 pounds) is applied in the direction of the
fork-bolt opening and parallel to the face of the latch (corresponding
to the transverse load test). Figure 1 depicts the loading direction for
this test. When in the secondary latched position, the primary latch and
striker assembly shall not separate when a load of 4 450 Newtons
(1000 pounds) is applied in the same direction.
S4.4.1.3 Load Test Three. The primary door latch and striker assembly
on back doors equipped with a latch and striker assembly at the bottom
of the door and that open upward shall not disengage from the fully latched
position when a load of 8 900 Newtons (2000 pounds) is applied
in a direction orthogonal to the directions specified in S4.4.1.1 and
S4.4.1.2 above.
S4.4.1.4 Inertia Load. The primary door latch shall not disengage
from the fully latched position when an inertia load of 30 g is applied
to the door latch system, including the latch and its activation mechanism
with the locking mechanism disengaged, in the directions specified in
S4.4.1.1, S4.4.1.2, and S4.4.1.3.
S4.4.1.5 Auxiliary Door Latches. Each auxiliary back door latch
and striker assembly shall be provided with a fully latched position and
shall comply with the requirements specified in S4.4.1.1, S4.4.1.2, and
S4.4.1.4.
S4.4.2 Door Locks. Each back door system equipped with interior
door handles or that leads directly into a compartment that contains one
or more seating accommodations shall be equipped with a locking mechanism
with operating means in both the interior and exterior of the vehicle.
When the locking mechanism is engaged, both the inside and outside door
handles or other latch release controls shall be inoperative.
S4.4.3 Door Hinges
S4.4.3.1 Load Test One. Each back door hinge system shall support
the door and shall not separate when a load of 11 000 Newtons
(2500 pounds) is applied perpendicular to the hinge face plate (longitudinal
load test) such that the hinge plates are not compressed against each
other.
S4.4.3.2 Load Test Two. Each back door hinge system shall not
separate when a load of 8 900 Newtons (2000 pounds) is
applied perpendicular to the axis of the hinge pin and parallel to the
hinge face plate (transverse load test) such that the hinge plates are
not compressed against each other.
S4.4.3.3 Load Test Three. Each hinge system on back doors that
open upward shall not separate when a load of 8 900 Newtons (2000 pounds)
is applied in the direction of the axis of the hinge pin.
The track and slide combination or other supporting means for each sliding
door shall not separate when a total longitudinal load of 17 800 Newtons
(4000 pounds) is applied, with the door in the closed position.
S5.1.1 Door Latches
S5.1.1.1 Longitudinal and Transverse Loads. Compliance with paragraphs
S4.1.1.1 and S4.1.1.2 shall be demonstrated in accordance with paragraph
5 of Society of Automotive Engineers Recommended Practice J839, Passenger
Car Side Door Latch Systems, June 1991.
|
(3)
|
S5.1.1.2 Inertia Load. Compliance with S4.1.1.3 shall be demonstrated
by approved tests or in accordance with paragraph 6 of Society of Automotive
Engineers Recommended Practice J839, Passenger Car Side Door Latch
Systems, June 1991.
S5.1.2 Door Hinges. Compliance with S4.1.2 shall be demonstrated
in accordance with paragraph 4 or 5, as appropriate, of Society of Automotive
Engineers Recommended Practice J934, Vehicle Passenger Door Hinge Systems,
July 1982. For piano-type hinges, the hinge spacing requirements of SAE
J934 shall not be applicable and arrangement of the test fixture shall
be altered, as required, so that the test load is applied to the complete
hinge.
S5.2.1 Door Latches. Compliance with S4.2.1 shall be demonstrated
in accordance with paragraphs 5.1 and 5.3, SAE Recommended Practice J839,
Passenger Car Side Door Latch Systems, June 1991. An equivalent
static test fixture may be substituted for that shown in Figure 2 of SAE
J839, if required.
S5.2.2 Door Hinges. Compliance with S4.2.2 shall be demonstrated
in accordance with paragraph 4 or 5, as appropriate, of SAE Recommended
Practice J934, Vehicle Passenger Door Hinge Systems, July 1982.
For piano-type hinges, the hinge spacing requirement of SAE J934 shall
not be applicable and arrangement of the test fixture shall be altered,
as required, so that the test load is applied to the complete hinge.
Compliance with S4.3 shall be demonstrated by applying an outward transverse
load of 8 900 Newtons (2000 pounds) to the load-bearing members at the
opposite edges of the door [17 800 Newtons (4000 pounds) total].
The demonstration may be performed either in the vehicle or with the door
retention components in a bench test fixture.
S5.4.1 Door Latches
S5.4.1.1 Load Tests One, Two, and Three. Compliance with S4.4.1.1,
S4.4.1.2, and S4.4.1.3 shall be demonstrated in the same manner as specified
in S5.1.1.1, except that the loads shall be in the directions specified
in S4.4.1.1, S4.4.1.2, and S4.4.1.3. The same test device may be used
for Load Tests Two and Three.
S5.4.1.2 Inertia Load. Compliance with S4.4.1.4 shall be demonstrated
in the same manner as specified in S5.1.1.2.
S5.4.2 Door Hinges. Compliance with S4.4.3.1, S4.4.3.2, and S4.4.3.3
shall be demonstrated in the same manner as specified in S5.1.2, except
that the loads shall be in the directions specified in S4.4.3.1, S4.4.3.2,
and S4.4.3.3. The same test device may be used for Load Tests Two and
Three.
Compliance with S4.5 shall be demonstrated by applying an outward longitudinal
load of 8 900 Newtons (2000 pounds) to the load-bearing members at the
opposite edges of the door [17 800 17 000
Newtons (4000 pounds) total]. The demonstration may be performed either
in the vehicle or with the door retention components in a bench test fixture.
|
Figure 1 — Top View of a Typical Back Door Latch
ENDNOTE:
* The numbers in parentheses in the margin refer to subsections
of section
206 of the Regulations that supersede the requirements of the TSD provision.
|